איך להדביק פינה עגולה לגבס | פינה קשתית

איך להדביק פינה עגולה לגבס | פינה קשתית


Hello My name is Michael in this video we will continue build a round shelf of drywall in the first video we made basic installation in this video we will do Painting works set the corners puttying and painting in front of everything important glue the connection between wall and shelf it’s quick-drying polymer glue spread glue and then wet your finger in soap and water and hold the finger on the glue with a finger make a beautiful connection same doing on the other hand this will further strengthen the shelf now the shelf is still moving a little but when the glue dries the shelf will not move Now we take a corner Arched corner this is a special corner that bends I recommend using plastic arched corner this is the best option of all in the installation of drywall factory corner length 3 meters corner needs to be cut at the end in the shape of a triangle we check that the corner fits in length corner to lie down freely on the shelf and then we temporarily screw corner to the shelf temporarily I screwed a screw from the bottom but then I will screw all the screws on top of the shelf better screw on top so the corner is better pressed against the shelf temporarily fasten corner to the shelf these are short screws which do not reach the metal structure of the shelf it’s temporary and the screws should not tighten the corner screws are screwed into gypsum only not in metal now you need to make sure that the corner fits snugly on the shelf note that the edge of the corner rises above the entire shelf this is normal you need to make sure that the distance between the corner and the shelf is the same in all places if the corner sticks out somewhere need to press it tightly do the same thing below the shelf is still moving a little when the glue dries the shelf will not move we check that the corner does not stick out where also need to make sure that the distance between the two corners is the same now we need to glue the corner with putty for this purpose i use gypsum-based putty at this stage of work this putty has advantages in general, you can use the usual chalk-based putty gypsum putty has an advantage at this stage of work this material does not shrink and gypsum putty dries faster in one and a half – two hours this material dries up Now apply a layer of putty on the corners if you use ordinary putty drying time may take up to 24 hours gypsum putty will dry in a couple of hours no matter what thickness the layer you apply apply a layer on only one side of the corners where there are no screws after the material has dried you can unscrew the screws it is important that the corner is always clean from dry putty as it may interfere apply evenly a new coat of putty corner edge controls layer thickness now apply a layer of putty to the second side of the corner do the same thing on the second side of the shelf unscrew the screws and apply a layer of gypsum putty at this stage of work is not important so that the putty is very smooth this material has one task glue the corners and apply the initial filling important during the application of putty make sure the tip of the corner is clean from excess putty at the same time you can cover all the screws after putty dries you can take not rough sandpaper and remove all the bumps also clean the tip of the corners the tip of the corners should always be clean the tip of the corners will control putty layer thickness at all stages of work the tip of the corners should be clean from putty the same shelf before the second putty must be clean from any bumps and residues of putty so that all kinds of crumbs do not interfere with smooth puttying remove with a clean spatula all that can interfere with smooth puttying Now we use ordinary chalk-based putty apply a layer of putty first apply a layer and then smooth apply and smooth putty the vertical part of the shelf in the process of filling, do not forget remove excess material from the tip of the corner after the putty has dried you can start grinding with sandpaper this is intermediate sanding use sandpaper P180 or P120 any strips need to be removed bumps and defects in circular motions pass over the entire area of the shelf slowly, gently grind the putty I took a wooden cube and wrapped it with sandpaper remove all sand with a brush we also grind the vertical part of the shelf more delicate sandpaper 400 or 350 putty layers are thinner on this part of the shelf now you can get the last coat of putty this layer is the thinnest and smoothest apply and remove putty the layer is thin and smooth you can always apply an extra coat if necessary and finish grinding we make with soft sandpaper p 350 or p 400 because the last layer was thin and smooth in circular movements, slowly grinding the putty it looks like a shelf after sanding everything is smooth and even no scratches and stripes now we need to primer the putty primer strengthens putty the primer is absorbed into the putty and strengthens it inside and out after priming it is impossible to grind putty additional primer improves adhesion of the paint to the putty also if dust remains after grinding the primer will eliminate it carefully primed the entire putty area the primer will make the filler a homogeneous mass now we start painting for painting we will use oil paint oil paint has several advantages it’s stronger paint this paint is washable in the future, the shelf can be wiped with a wet rag also this paint looks more effective this paint looks smoother and more glossy we paint with a micro wool roller microfiber roller in the corners we pass with an plain brush it is important to smooth the paint well with a roller remove all smudges of paint it is important to make sure that the paint looks the same no stripes and smoothly friends video came to an end this is the end result you can see that everything is smooth uniform and clean the shelf is evenly round in perfect shape thank you very much for watching if you liked the video click like if you have questions ask in the comments subscribe to the channel I will try to make another video thanks again for watching and see you soon

15 thoughts on “איך להדביק פינה עגולה לגבס | פינה קשתית

  1. Как обещал ,продолжаю смотреть ,не люблю друзьям портить статистику по просмотрам !

  2. ארוץ מעולה, מאוד עוזר לי. יש לי שאלה קצת לא קשורה לסרטון, אם תוכל לענות אשמח. איך לתקן מדרגות שניסדקו ונשברו בחדר המדרגות (עשויים מבלתות), כלומר איזה חומרים ניתן להשתמש לתיקון. תודה

  3. בוקר טוב מיכאל וכל הכבוד על העבודה היפה והנקיה
    בסרטון אחר שלך השתמשת באזור חיבור המדף לקיר בטיח גבס במקום סופר 7/היי-טאק. האם יש הבדל בתוצאות?
    האם במקום חומר קנאוף יוניפלוט אפשר להשתמש בכל חומר טיח גבס והוא גם יתיבש באותה המהירות ונקבל את אותם התוצרות?
    כל הכבוד על הסרטונים המצויינים. בהצלחה 🙂

  4. היי מיכאל קודם כל סרטונים מעולים 👌 יש לי שאלה אליך אני פשוט לא הכי מכיר- יש מספריים של irwin במבצע ב59 שקל במקום 145. המחירים של מספריים ראיתי בין 60 ל90 בארץ נניח. זה בצבע צהוב… זה טוב? או להתעקש רק ירוקות? מבחינת עבודות גבס

Leave a Reply

Your email address will not be published. Required fields are marked *